moxbox init

apps/tinyproxy/config/mixbox.conf

@@ -0,0 +1,23 @@
+#------------------【TinyProxy】--------------------
+tinyproxy() {
+
+	eval `mbdb export tinyproxy`
+	source /etc/mixbox/bin/base
+	echo "********* $service ***********"
+	echo "[${appinfo}]"
+	readsh "启动${appname}服务[1/0] " "enable" "1"
+	if [ "$enable" == '1' ]; then
+		read -p "修改${appname}端口号(`mbdb get ${appname}.main.port || echo 8888`)？[1/0] " res
+		if [ "$res" == '1' ]; then
+			read -p "请输入${appname}端口号(默认8888)：" res
+			mbdb set $appname.main.port="$res"
+		fi
+		readsh "请输入${appname}外网访问配置[1/0]" "openport" "1"
+		
+		${mbroot}/apps/${appname}/scripts/${appname}.sh restart
+	else
+		${mbroot}/apps/${appname}/scripts/${appname}.sh stop
+	fi
+	
+}
+#------------------【TinyProxy】--------------------

apps/tinyproxy/config/tinyproxy.conf

@@ -0,0 +1,228 @@
+##
+## tinyproxy.conf -- tinyproxy daemon configuration file
+##
+
+#
+# Name of the user the tinyproxy daemon should switch to after the port
+# has been bound.
+#
+#User root
+#Group root
+
+#
+# Port to listen on.
+#
+Port 8888
+
+#
+# If you have multiple interfaces this allows you to bind to only one. If
+# this is commented out, tinyproxy will bind to all interfaces present.
+#
+#Listen 192.168.0.1
+
+#
+# The Bind directive allows you to bind the outgoing connections to a
+# particular IP address.
+#
+#Bind 192.168.0.1
+
+#
+# Timeout: The number of seconds of inactivity a connection is allowed to
+# have before it closed by tinyproxy.
+#
+Timeout 600
+
+#
+# ErrorFile: Defines the HTML file to send when a given HTTP error
+# occurs.  You will probably need to customize the location to your
+# particular install.  The usual locations to check are:
+#   /usr/local/share/tinyproxy
+#   /usr/share/tinyproxy
+#   /etc/tinyproxy
+#
+# ErrorFile 404 "/usr/share/tinyproxy/404.html"
+# ErrorFile 400 "/usr/share/tinyproxy/400.html"
+# ErrorFile 503 "/usr/share/tinyproxy/503.html"
+# ErrorFile 403 "/usr/share/tinyproxy/403.html"
+# ErrorFile 408 "/usr/share/tinyproxy/408.html"
+
+# 
+# DefaultErrorFile: The HTML file that gets sent if there is no
+# HTML file defined with an ErrorFile keyword for the HTTP error
+# that has occured.
+#
+DefaultErrorFile "/usr/share/tinyproxy/default.html"
+
+#
+# StatFile: The HTML file that gets sent when a request is made
+# for the stathost.  If this file doesn't exist a basic page is
+# hardcoded in tinyproxy.
+#
+StatFile "/usr/share/tinyproxy/stats.html"
+
+#
+# Where to log the information. Either LogFile or Syslog should be set,
+# but not both.
+#
+# Logfile "/var/log/tinyproxy.log"
+# Syslog On
+
+#
+# Set the logging level. Allowed settings are:
+#	Critical	(least verbose)
+#	Error
+#	Warning
+#	Notice
+#	Connect		(to log connections without Info's noise)
+#	Info		(most verbose)
+# The LogLevel logs from the set level and above. For example, if the LogLevel
+# was set to Warning, than all log messages from Warning to Critical would be
+# output, but Notice and below would be suppressed.
+#
+LogLevel Error
+
+#
+# PidFile: Write the PID of the main tinyproxy thread to this file so it
+# can be used for signalling purposes.
+#
+PidFile "/var/run/tinyproxy.pid"
+
+#
+# Include the X-Tinyproxy header, which has the client's IP address when
+# connecting to the sites listed.
+#
+#XTinyproxy mydomain.com
+
+#
+# Turns on upstream proxy support.
+#
+# The upstream rules allow you to selectively route upstream connections
+# based on the host/domain of the site being accessed.
+#
+# For example:
+#  # connection to test domain goes through testproxy
+#  upstream testproxy:8008 ".test.domain.invalid"
+#  upstream testproxy:8008 ".our_testbed.example.com"
+#  upstream testproxy:8008 "192.168.128.0/255.255.254.0"
+#
+#  # no upstream proxy for internal websites and unqualified hosts
+#  no upstream ".internal.example.com"
+#  no upstream "www.example.com"
+#  no upstream "10.0.0.0/8"
+#  no upstream "192.168.0.0/255.255.254.0"
+#  no upstream "."
+#
+#  # connection to these boxes go through their DMZ firewalls
+#  upstream cust1_firewall:8008 "testbed_for_cust1"
+#  upstream cust2_firewall:8008 "testbed_for_cust2"
+#
+#  # default upstream is internet firewall
+#  upstream firewall.internal.example.com:80
+#
+# The LAST matching rule wins the route decision.  As you can see, you
+# can use a host, or a domain:
+#  name     matches host exactly
+#  .name    matches any host in domain "name"
+#  .        matches any host with no domain (in 'empty' domain)
+#  IP/bits  matches network/mask
+#  IP/mask  matches network/mask
+#
+Upstream socks5 127.0.0.1:1082
+
+#
+# This is the absolute highest number of threads which will be created. In
+# other words, only MaxClients number of clients can be connected at the
+# same time.
+#
+MaxClients 100
+
+#
+# These settings set the upper and lower limit for the number of
+# spare servers which should be available. If the number of spare servers
+# falls below MinSpareServers then new ones will be created. If the number
+# of servers exceeds MaxSpareServers then the extras will be killed off.
+#
+MinSpareServers 5
+MaxSpareServers 20
+
+#
+# Number of servers to start initially.
+#
+StartServers 10
+
+#
+# MaxRequestsPerChild is the number of connections a thread will handle
+# before it is killed. In practise this should be set to 0, which disables
+# thread reaping. If you do notice problems with memory leakage, then set
+# this to something like 10000
+#
+MaxRequestsPerChild 0
+
+#
+# The following is the authorization controls. If there are any access
+# control keywords then the default action is to DENY. Otherwise, the
+# default action is ALLOW.
+#
+# Also the order of the controls are important. The incoming connections
+# are tested against the controls based on order.
+#
+#Allow 127.0.0.1
+#Allow 192.168.1.0/25
+
+#
+# The "Via" header is required by the HTTP RFC, but using the real host name
+# is a security concern.  If the following directive is enabled, the string
+# supplied will be used as the host name in the Via header; otherwise, the
+# server's host name will be used.
+#
+ViaProxyName "tinyproxy"
+
+#
+# The location of the filter file.
+#
+#Filter "/etc/tinyproxy/filter"
+
+#
+# Filter based on URLs rather than domains.
+#
+#FilterURLs On
+
+#
+# Use POSIX Extended regular expressions rather than basic.
+#
+#FilterExtended On
+
+#
+# Use case sensitive regular expressions.
+#                                                                         
+#FilterCaseSensitive On     
+
+#
+# Change the default policy of the filtering system.  If this directive is
+# commented out, or is set to "No" then the default policy is to allow
+# everything which is not specifically denied by the filter file.
+#
+# However, by setting this directive to "Yes" the default policy becomes to
+# deny everything which is _not_ specifically allowed by the filter file.
+#
+#FilterDefaultDeny Yes
+
+#
+# If an Anonymous keyword is present, then anonymous proxying is enabled.
+# The headers listed are allowed through, while all others are denied. If
+# no Anonymous keyword is present, then all header are allowed through.
+# You must include quotes around the headers.
+#
+#Anonymous "Host"
+#Anonymous "Authorization"
+
+#
+# This is a list of ports allowed by tinyproxy when the CONNECT method
+# is used.  To disable the CONNECT method altogether, set the value to 0.
+# If no ConnectPort line is found, all ports are allowed (which is not
+# very secure.)
+#
+# The following two ports are used by SSL.
+#
+ConnectPort 443
+ConnectPort 563

apps/tinyproxy/config/tinyproxy.uci

@@ -0,0 +1,7 @@
+service="TinyProxy"
+appname="tinyproxy"
+needver="0.0.1"
+supports="linux_arm,linux_mips,linux_x86_64"
+appinfo="轻量级的Http代理工具"
+newinfo=""
+version="0.0.2"

apps/tinyproxy/config/version.txt

@@ -0,0 +1 @@
+1.1.5

apps/tinyproxy/scripts/tinyproxy.sh

@@ -0,0 +1,62 @@
+#!/bin/sh 
+source /etc/mixbox/bin/base
+eval `mbdb export tinyproxy`
+
+port=$(mbdb get ${appname}.main.port) || port=8888
+binname=${appname}
+
+start () {
+
+	result=$(ps | grep ${mbroot}/apps/${appname}/bin/${appname} | grep -v grep | wc -l)
+    	if [ "$result" != '0' ];then
+		logsh "【$service】" "${appname}已经在运行！"
+		exit 1
+	fi
+	logsh "【$service】" "正在启动${appname}服务... "
+	if [ ! -f ${mbroot}/apps/${appname}/bin/${appname} ]; then
+		bincheck ${binname} 
+    	[ $? -eq 0 ] && ln -sf $(which $binname) ${mbroot}/apps/${appname}/bin/${appname} 
+	fi
+	cp -rf ${mbroot}/apps/${appname}/config/${appname}.conf ${mbtmp}
+	sed -i "s/Port 8888/Port ${port}/" ${mbtmp}/${appname}.conf
+	open_port
+    write_firewall_start
+	daemon ${mbroot}/apps/${appname}/bin/${appname} -c ${mbtmp}/${appname}.conf
+	if [ $? -ne 0 ]; then
+            logsh "【$service】" "启动${appname}服务失败！"
+    else
+            logsh "【$service】" "启动${appname}服务完成！"
+    fi    
+
+}
+
+stop () {
+
+	logsh "【$service】" "正在停止${appname}服务... "
+	close_port
+	remove_firewall_start
+	killall -9 ${appname} &> /dev/null
+	
+
+}
+
+
+status() {
+
+	result=$(pssh | grep ${mbroot}/apps/${appname}/bin/${appname} | grep -v grep | wc -l)
+	if [ "$result" == '0' ]; then
+		status="未运行|0"
+	else
+		status="运行端口号: ${port}|1"
+	fi
+	mbdb set $appname.main.status="$status" 
+
+}
+
+case "$1" in
+	start) start ;;
+	stop) stop ;;
+	restart) stop; start ;;
+	reload) close_port && open_port ;;
+	status) status ;;
+esac